1 - Glazing Caps - One cap fits all, 16mm 24/25mm and 35mm.
- No gasket to fit - all co-extruded soft edged seals, colour matched - no black lines.
- Designed for Glass or Polycarbonate.
- Single knock on position, cannot be over or under tensioned.
- Twin under cladding fits all options including hips, identical internal width (whatever the bar).
- Hi-heat brown formula (90degreesC) ensures no warping or twisting.
- Warm White, High (blue White, Mahogany, Woodgrain and Rosewood
- Any RAL colour to order
- Aluminium option available
- Thermally insulated
2 - Glazing Bars The four bars + hips are designed to cover ever spanning requirement and situation. - S150 max 2800mm span*
- S250 max 3950mm span*
- S300 max 4400mm span*
- S500 max 4900mm span*
The Newdawn lean-to roof is manufactured from standard parts and requires only the addition of an internal seal to allow a 2.5 degree pitch roof which can include a roof vent and will span 4900mm unsupported. *Subject to glazing widths, material and locations 3 - Rafter End Caps/Bolster Bars - Cast aluminium End Caps with a powdered coated finish.
- Acts as a Glass Stop - can't fall off.
- Can be Personalised with your logo
- Strong Lug Fixings into box section rafter.
- Retains polycarbonate sheets
- Easy to clean & maintain, stays looking good.
- Offset provides built in drainage.
Bolster bars are designed to increase the span and avoid the need for an expensive portal frame, supplied with snap on aluminium under cladding and end casting the bars are both decorative and functional. 4 - Ringbeam/Eavesbeam - Strong Box Section Construction.
- Slide and click plates locate rafters.
- Snap on glazing support with triple seals.
- Peel back adhesive foam glazing support.
- Complete structural ring for added strength.
- Range of fixings and adjustable corner connectors.
- Box section reinforcement option for long spans.
- Carriers Aluminium Gutter.
- Range of plain and decorative internal cladding.
5 - Gutters - Heavy duty Aluminium Gutter in stylish Ogee shape.
- Powder coated 65 micron thick.
- No levels to find. no brackets to fix.
- Simple - Just hooks on to the ringbeam.
- Dentil moulding clips on - no increased height.
- New Deeper option for 35mm rods.
- No Warping, Discolouration or Distortion.
- Standard angle inserts snap into place.
- Cast aluminium or PVC corner covers.
6 - Ridge and Wall Plate - Two part colour matched powder coated aluminium ridge/wall plate
- Adjustable depths for 16/25/32/35mm glazing
- Slide and click rafter plates
- Snap on ridge filler with flexible double seals
- Snap on ovolo moulded undercladding with pitch adjustment.
- Fully adjustable cast aluminium spider ready drilled and tapped for fan fitting.
- Low voltage ridge lighting system in chrome or gold finish.
- Built in wiring ducts for lighting and fan.
- Cast Aluminium Finials.
- Slide fit cresting or snap on closure for a smooth modern look .
7 - Spider Cap - Cap fits right down to the glazing material.
- No Silicone, No Foam, No Brush Seals, No Leaks.
- Fully engineered fit minimises wind velocity - no gaps, looks good.
- Finial & Cresting Clamps spider cover down.
- Pre-formed internal spider cover with single threaded fixings.
- Cast aluminium spider cap available.
8 - Valleys / Wall Bar - Adjustable Valley - 5 to 35 degrees either side with dual track to provide a continuous seal & snap on under cladding.
- Central spine in colour matched powder coated aluminium.
- Valley end caps for a quality finish.
- Wings in mill finish with twin tracks, captive bolts and continous seals.
- Insulated PVCu under cladding and snap on cap.
- Dedicated Wall bar with built in up stand for flashing.
- Easier to fix, uses standard rafter capping.
- Takes standard twin underclad - preserves sight lines
- Available in S150 and S250 systems.
|